Most access control quotes go wrong in the parts nobody counted: the exit button, the break glass unit, the door contact, the second power supply. This planner lists them for you. Tell it how many doors, how many users, whether they use a finger, a face, a card or a PIN, and which lock each door gets, and it works out the readers, controllers, locks, exits, the current at 12 V, the power supply and battery, the cable and a rough price. For how the pieces fit together, read access control systems.
How the planner counts
Each door gets a reader outside, a lock, a door contact and a request to exit button inside; tick the exit reader box and the button becomes a second reader. A maglock door also gets a green break glass unit, because a maglock is fail safe. Controllers are counted at four doors a board; many boards run one or two.
The load adds each part's typical working current from makers' datasheets: a fingerprint terminal about 500 mA, a face terminal about 1,000 mA, a card reader under 100 mA, a 280 kg maglock about 500 mA. The supply is the next size up with a quarter spare.
Reading the parts list
- Readers: one a door, two where you read people out as well, for anti-passback or a roll call.
- Controllers: the boards that decide who opens what and when, and keep the event log.
- Load at 12 V: what the supply must give with every lock held and every reader awake.
- Battery: sized for the backup hours you set, with the same sums as the backup battery calculator.
- Cable: 30 m a door is our default; change it once someone has walked the route.
Where door plans go wrong
- Doors pop open in load shedding: maglocks on a supply with no battery, or a battery that died years ago.
- Readers reboot when a lock releases: one small supply shared by too many parts; split readers and locks.
- Fire exits stay locked: no link to the fire alarm. Check with the fire engineer or the fire department which doors must release.
- Faces fail at the front door: the terminal faces the afternoon sun through glass.
- The system fills up: more users than one terminal holds, with no software to manage them.
From the parts list to quotes
Put the doors, users and credential on the request below. Installers can then quote the same scope, door by door, and you can compare like with like: the reader model and its rating outdoors, the lock and bracket, the exit device, the contact, the controller, the supply and battery, cable and conduit, the software licence for your users, enrolment, training and the fire alarm link. Ask each one for the backup time in hours and for the company's PSIRA registration. The installation page covers what happens on site.
Sources
- Access control maker, fingerprint terminal datasheet: power supply DC 12 V 1 A; power consumption up to 4.0 W standby and up to 6.0 W working (500 mA at 12 V); 3,000 fingerprints, 30,000 cards, 30,000 users, 150,000 records; fingerprint comparison time 1.5 s; 1:N and 1:1
- Access control maker, fingerprint reader datasheet: 12 V DC 0.5 A supply; up to 1.0 W standby and 1.7 W working (about 140 mA at 12 V); 3,000 fingerprints; recognition 1.5 s or less
- Access control maker, face recognition terminal datasheet: DC 12 V 2 A supply; power consumption 12 W (1,000 mA at 12 V); 50,000 faces; 100,000 records; face recognition 0.35 s; face to camera 0.3 to 2.0 m
- Access control maker, 13.56 MHz card reader datasheet: 9 to 15 VDC, 100 mA; up to 0.9 W standby and 1 W working (about 83 mA at 12 V); 13.56 MHz cards
- Reader maker, 125 kHz proximity reader and keypad datasheet: +5 to 16 VDC; current draw 70 mA typical, 110 mA peak at 12 VDC; read range up to 176 mm; Wiegand; IP67
- Access control maker, two door controller datasheet: two doors; power consumption up to 3 W (250 mA at 12 V) before readers and locks; supplies 4 readers at 12 V, 500 mA or less each, and 2 locks at 12 V, 1.2 A or less each; 100,000 users and cards, 500,000 records; 4 RS-485 reader ports and 4 Wiegand inputs
- Maglock maker, single door magnetic lock specification: 180 kg (350 lbs): 12 V 300 mA, 24 V 150 mA; 280 kg (600 lbs): 12 V 500 mA, 24 V 250 mA; 500 kg (1200 lbs): 12 V 420 mA, 24 V 210 mA; 12/24 VDC by jumper; the plate pivots on a rubber washer to take up small misalignment
- Security distributor, 280 kg magnetic lock: 280 kg holding force, fail safe; 500 mA at 12 V DC, 250 mA at 24 V DC
- Lock maker, electric strike datasheet: dual voltage 12/24 VDC; current draw 250 mA at 12 VDC, 150 mA at 24 VDC; fail safe or fail secure chosen on site; holding strength 700 kg
- Battery conference paper, ageing factors in battery sizing: IEEE 485 sizing for lead acid uses an ageing factor of 1.25, so a battery at its end of life (80% of rated capacity) still carries the load: 80% of 125% equals 100%
- Engineering calculator, UPS battery sizing for physical security: Ah = load x hours / (efficiency x volts x usable depth of discharge); sealed lead acid (VRLA) limited to 80% depth of discharge; lithium (LiFePO4) 90 to 95%
- Vanderbijlpark security wholesaler, access control category page 1: incl. VAT: 125 kHz proximity cards R8.26 to R17.94, 13.56 MHz cards R15.66 to R16.45, 125 kHz key tags R10.10 to R10.84, 13.56 MHz key tag R42.78, UHF thin sticker tag R14.63, exit button R26.08, resettable break glass unit R124.20
- Vanderbijlpark security wholesaler, access control category page 3: incl. VAT: 125 kHz and 13.56 MHz slave card readers R472.43 to R617.80, card reader with keyboard R542.75, no touch exit sensor R517.50, 280 kg indoor maglock R688.02
- Vanderbijlpark security wholesaler, access control category page 5: incl. VAT: 500 kg outdoor maglock R1,526.24, 500 kg maglock R1,899.64, fingerprint terminal R1,769.37, 7 inch analogue video intercom kit R1,738.39, metal case and power supply for controllers R1,501.10, palm and fingerprint clocking terminal R1,415.88
- Vanderbijlpark security wholesaler, access control category page 6: incl. VAT: outdoor fingerprint slave readers R2,553.90, 1 door controller R3,013.99, 4.3 inch video intercom kit R2,948.12, app controlled smart lock R3,092.65, fingerprint smart lock with Wi-Fi R3,232.93
- Vanderbijlpark security wholesaler, access control category page 7: incl. VAT: outdoor face terminal R3,800.59, face recognition terminal R4,165.44, 1 door controllers R3,931.69 to R4,609.48, fingerprint access control device kit R4,279.44, 7 inch video intercom kit R3,708.26
- Vanderbijlpark security wholesaler, access control category page 8: incl. VAT: outdoor fingerprint terminals R5,798.02 and R7,799.73, face recognition terminal R6,926.01, 2 door controllers R5,856.24 to R6,736.76, 4 door controller R7,736.21, smart door lock R6,977.14, IP video intercom kit R5,489.84
- Randburg security shop, access control and camera search results: incl. VAT: number plate recognition camera R10,048, 280 kg maglock R879, face and fingerprint terminals R3,999 to R4,799, fingerprint and card reader R1,499, 4 door controller R5,995 (out of stock)
- Online shopping site, Durban security seller, electric strike listing: VAT n/s: standard electric strike R504, in stock
- Online shopping site, Durban security seller, keypad and card reader listing: VAT n/s: compact keypad and card reader R2,004; listing closed, no sale
- Online shopping site, Johannesburg security seller, access control power supply listing: VAT n/s: 13.6 V 3 A access control power supply in a lockable metal box R859, 7 Ah battery not included; listing closed
- Gauteng security and network distributor, fail secure electric strike product page: incl. VAT: fail secure electric strike R2,335.65 retail, sold out
- Johannesburg handyman and installer site, biometric access control prices: VAT n/s for per door figures: fingerprint a door residential R6,000 to R12,000, commercial R8,000 to R15,000; face recognition residential R8,000 to R18,000, commercial R12,000 to R25,000; keypad or card R2,000 to R8,000; call-out R600 to R900; labour R500 to R700 an hour
- Johannesburg handyman and installer site, access control installation cost: VAT n/s: single door all inclusive R5,000 to R8,000; 3 to 10 doors R4,500 to R7,000 a door; 26 doors or more R3,500 to R5,500 a door; annual maintenance R2,400 to R4,500 for a R30,000 system
Frequently asked questions
Why does a maglock door need a break glass unit?
Can I run fingerprint terminals and maglocks from one power supply?
How many doors can one controller run?
Who prices the parts on this list?
More calculators and tools
- Maglock calculatorThe holding force class, bracket, current and supply for one door
- Backup battery calculatorThe battery in amp hours to carry readers and locks through outages
- Gate motor calculatorMotor class by gate mass and width, and the cycles a battery gives
- Clocking terminal calculatorHow many clocking terminals clear the shift change in time
- Turnstile lane calculatorLanes of tripod, speed gate or full height turnstile for your peak
- Biometric error rate calculatorFalse rejects and false accepts in people a day at your door
- Electric fence calculatorWire, brackets, warning signs and earth spikes for your fence
