Get free quotes

Free calculator, nothing to sign up for

Maglock calculator

Choose the kind of door, whether it swings towards or away from the lock side, glass or framed, the security you need and the supply voltage: see the holding force class, the bracket, the current and what it suits.

A silver maglock on the head of an aluminium door frame with its armature plate on the closed glass door below
Verifying…GrantedAC-04
Maglock calculatorDoor in, holding force out
Runs in
your browser
Sent
nothing
Class to buy
-
Holding force
-
Bracket
-
Current
-
Suits
-

A bigger number on the box does not make a door safer if the plate only touches the magnet on one corner. Holding force is rated with the armature plate flat and full on the magnet, so the bracket matters as much as the class. This calculator starts from the door: what it is made of, which way it swings relative to the lock, glass or framed, and how much security it needs. It names the class to buy, the bracket, the current at 12 V or 24 V and the doors that class suits. More on magnetic locks.

How the class is chosen

Each door type carries a smallest class: 60 kg for a cabinet, 180 kg for glass, 280 kg for an internal door, 500 kg for an outside or steel door where the maglock is the only lock, and a sealed outdoor class for a gate. Those come from makers' guidance: one advises about 300 kg for an internal door and 500 kg as the minimum on an outside door, another says glass usually needs less force. Tick higher security and the tool steps up one class. Currents come from makers' datasheets for each class.

Brackets: if this, then that

  • If the door swings towards the lock side: the magnet goes on the frame head with an L bracket and the plate sits on the door.
  • If it swings away from the lock side: add a Z and L bracket so the plate meets the magnet face.
  • If the door is frameless glass: U brackets clamp to the glass, because you cannot screw into it.
  • If the frame head is too shallow: ask for a slimline lock or a different bracket before you buy.
  • If it is a gate: use a sealed outdoor lock and a gate stop so the plate lands square.

Current, voltage and the fire alarm

A maglock draws its current all the time the door is locked, which is most of the day and night. At 24 V it draws about half the current of 12 V for the same force, which helps on long cable runs where voltage drops. Many locks switch between the two with a jumper; check it before you power up.

Because a maglock is fail safe, it needs a battery backed supply, a request to exit button, a break glass unit and a release from the fire alarm. Check with the fire engineer or the fire department which doors must open on alarm.

Taking the class to an installer

Note the class, the bracket and the voltage, and add them to the request below with the door count. An installer can then quote the lock with the right bracket, the supply and battery, the exit button, the break glass unit and the door closer, rather than a bare magnet. Ask whether the lock has a built in door status output and a bond sensor. For the battery size across several doors, use the backup battery calculator, and for the whole door, the access control planner.

Sources

Frequently asked questions

Is a 280 kg maglock strong enough for my front door?
As the only lock on an outside door, makers say no: they advise 500 kg as the minimum there, and a mechanical lock for nights if possible. A 280 kg lock suits most internal doors used during the day. The real strength also depends on the frame and the plate alignment, so a bent frame weakens any class.
Why does my maglock hum or let go when pushed?
Usually the plate is not meeting the magnet flat: a sagging door, a loose plate or a door closer that does not pull it all the way. Dirt or rust on the faces and low voltage at the end of a long cable do the same. Clean both faces, check the voltage at the lock and adjust the closer first.
Should I choose 12 V or 24 V?
Use what the controller and supply already run. A 24 V lock draws about half the current, so voltage drop on a long cable is smaller and one supply carries more locks. Many maglocks take either by moving a jumper inside. Do not mix them up on one supply without checking every part's rating.
Who will fit the maglock and its bracket?
Use the request below with the doors, the class and the bracket. We pass it to independent access control installers and locksmiths near you, who quote you directly and usually look at the door and frame first. We do not sell or install locks ourselves.

More calculators and tools

Free quote request, no obligation

Request magnetic locks quotes

Fill in the schedule the way an installer would on a site survey: what the site is, the doors or the gate, who must get through and how, and the power and network there. Installers and suppliers in your area quote you directly.

Door schedule and requestMagnetic Locks
Req
MAG-122
Code
AC-04
Date
2026-11-22

01The job

02How many (optional, it helps the quote)

Your requestrule of thumb

-
-
-
-
-
-
Estimate
-

A rule of thumb for the request, not an installer's design.

03The site and timing

04Your list (optional)

  1. 01
  2. 02
Up to 12 lines: readers, locks, cards, motors, intercoms or work.
Needs and options

05Your details

Free and no obligation. By sending you agree that we may share your request with suitable installers, integrators, suppliers and technicians. See our privacy policy.

Get free quotes